Windows XP and Windows 2003 Password Loophole Work Around
Windows XP and Windows 2003 Password Loophole Work Around
If you are trying to log in locally to a Windows XP or Windows 2003 computer and you do not remember the password you can use the following steps to reset the password on the local account. (For instructor-led Windows 7 training, see our course schedule.)
- Place your Windows XP CD in your cd-rom and start your computer (it’s assumed here that your XP CD is bootable – as it should be – and that you have your bios set to boot from CD)
- Keep your eye on the screen messages for booting to your cd Typically, it will be “Press any key to boot from cd”
- Once you get in, the first screen will indicate that Setup is inspecting your system and loading files.
- When you get to the Welcome to Setup screen, press ENTER to Setup Windows now
- The Licensing Agreement comes next – Press F8 to accept it.
- The next screen is the Setup screen which gives you the option to do a Repair.It should read something like “If one of the following Windows XP installations is damaged, Setup can try to repair it”
- Use the up and down arrow keys to select your XP installation (if you only have one, it should already be selected) and press R to begin the Repair process.
- Let the Repair run. Setup will now check your disks and then start copying files which can take several minutes.
- Shortly after the Copying Files stage, you will be required to reboot. (this will happen automatically – you will see a progress bar stating “Your computer will reboot in 15 seconds”
- During the reboot, do not make the mistake of “pressing any key” to boot from the CD again! Setup will resume automatically with the standard billboard screens and you will notice Installing Windows is highlighted.
- Keep your eye on the lower left hand side of the screen and when you see the Installing Devices progress bar, press SHIFT + F10. This is the security hole! A command console will now open up giving you the potential for wide access to your system.
- At the prompt, type CPL and press Enter. Voila! You have just gained graphical access to your User Accounts in the Control Panel.
- Now simply pick the account you need to change and remove or change your password as you prefer. If you want to log on without having to enter your new password, you can type control userpasswords2 at the prompt and choose to log on without being asked for password. After you’ve made your changes close the windows, exit the command box and continue on with the Repair (have your Product key handy).
- Once the Repair is done, you will be able to log on with your new password (or without a password if you chose not to use one or if you chose not to be asked for a password). Your programs and personalized settings should remain intact.
Until next time … RIDE SAFE!
For instructor-led Windows 7 training, see our course schedule.
Rick Trader
Windows Server Instructor – Interface Technical Training
Phoenix, AZ
You May Also Like
A Simple Introduction to Cisco CML2
0 3794 0Mark Jacob, Cisco Instructor, presents an introduction to Cisco Modeling Labs 2.0 or CML2.0, an upgrade to Cisco’s VIRL Personal Edition. Mark demonstrates Terminal Emulator access to console, as well as console access from within the CML2.0 product. Hello, I’m Mark Jacob, a Cisco Instructor and Network Instructor at Interface Technical Training. I’ve been using … Continue reading A Simple Introduction to Cisco CML2
Configuring Windows Mobility Center and How to Turn it On and Off
1 1434 1Video transcription Steve Fullmer: In our Windows training courses, we often share information about the Windows 8.1 Mobility Center. Mobility Center was introduced for mobile and laptop devices in Windows 7. It’s present and somewhat enhanced in Windows 8. Since we don’t have mobile devices in our classrooms, I decided to take a little bit … Continue reading Configuring Windows Mobility Center and How to Turn it On and Off
OSPF Adjacency Troubleshooting Solution – Getting Close to the OSPF adj
0 249 1In this video, Cisco CCNA & CCNP instructor Mark Jacob shows how to troubleshoot OSPF Adjacency issues by showing the distance between routers with the show ip ospf neighbor command.